Lighting Procurement: Four Scenarios, Four Different Vendor Strategies
-
Scenario 1: You're maintaining fixtures you already own, and the product line is quietly dying
-
Scenario 2: Decorative and feature lighting, where access drives the cost
-
Scenario 3: Hardwired under-cabinet lighting — the labor is the price
-
Scenario 4: Multi-site buying and controls lock-in
-
How to figure out which scenario you're in
I've reviewed more than 340 lighting quotes over the past six years. If I've learned anything, it's that there's no single "best" lighting vendor — only the best vendor for the situation you're actually in.
Most of the procurement questions I field about lighting fall into four buckets. Which bucket you're in decides what you should be comparing, and which number on the quote deserves suspicion.
Roughly:
- You're maintaining fixtures you already own, and the product line is quietly dying.
- You're specifying decorative or feature lighting where maintenance access matters more than the fixture price.
- You're hardwiring under-cabinet lighting, and the electrician is the real line item.
- You're buying across multiple sites, and controls lock-in decides your ten-year cost.
Here's how I sort them.
Scenario 1: You're maintaining fixtures you already own, and the product line is quietly dying
This is the scenario that blindsides facilities teams. A Biax 2D lamp in an entrance downlight burns out, you reorder the same part number, and six weeks later the distributor tells you it's backordered indefinitely. That's when who owns GE Lighting stops being trivia and becomes a supply-chain problem.
For the record: GE Lighting hasn't been a General Electric division since 2020, when Savant Systems acquired the business. The GE name is licensed, not owned. That matters for procurement because ownership transitions tend to be followed by SKU rationalization — legacy compact fluorescent lines get consolidated, and the part numbers you've specced for a decade quietly go end-of-life.
The regulatory picture doesn't make it easier. The Department of Energy's general service lamp rules have been contested in court — a 2024 ruling vacated the agency's expanded definition, which has left a lot of fluorescent SKUs in limbo. I'm not going to pretend I can predict how that resolves, and neither should your vendor.
So what's the TCO move? Don't stockpile out of panic. Run the math on three options: (1) buy a two-year supply of GE Lighting Biax 2D lamps at today's price, (2) retrofit the fixtures to LED, (3) replace the fixtures entirely. In my experience, option 1 loses more often than people expect, because storage and re-lamping labor don't disappear — they just get deferred. And deferred costs have a habit of arriving in the same quarter.
One more thing: keep a spreadsheet of every discontinued SKU with the date you first heard the word "backorder." Six years of tracking has taught me that the first backorder is almost always the start of end-of-life, not a blip. I wish I'd built that habit three years earlier than I did.
"Looking back, I should have flagged the Biax 2D line for an end-of-life review in 2022, when our first distributor started quoting 8-week lead times. At the time, I treated it as a temporary supply hiccup. It wasn't."
Scenario 2: Decorative and feature lighting, where access drives the cost
This is where the sticker price lies to you the most. When you're buying from chandelier companies for a hotel lobby, or specifying a career spotlight rig over a vocational training workbench, the fixture itself is maybe 30% of the ten-year cost. The rest is access.
Ask one question before you sign: how do we service this thing? If the answer involves a scissor lift, a rigging crew, or removing a ceiling panel, that's your real cost driver. I've watched a $1,400 fixture with tool-less bottom access beat a $900 fixture that needed a lift every time a driver failed. Over eight years, the "cheaper" one cost us roughly 40% more.
Lead time is the other silent cost. Custom chandelier work often runs 10–16 weeks. If your project schedule assumes six, you're paying for that gap in change orders and overtime. It doesn't show up in the quote comparison at all, which is exactly why it gets missed.
Second question: does the manufacturer stock replacement parts, or is this a small shop that will pivot to a different product line in three years? This is especially true with chandelier companies that do custom work. A beautiful fixture with no replacement crystal or socket in year four is a demolition cost, not an asset.
And if a vendor claims their lamp is "mercury-free" or "fully recyclable," make them show the substantiation. Under the FTC Green Guides (16 CFR Part 260), environmental claims have to be backed by evidence — "recyclable" in particular means a substantial majority of consumers must actually have access to recycling for that material. If they can't point to documentation, that's a red flag, not a marketing detail.
Scenario 3: Hardwired under-cabinet lighting — the labor is the price
If you've ever looked up how to hard wire under cabinet lighting, you already know the fixture is the cheap part. The install is where the budget goes.
The basic sequence: kill the circuit, run NM cable from a junction box to each fixture location, mount the fixtures, connect the leads, and terminate everything in an accessible box per NEC Article 410 (NFPA 70). If there's no existing circuit nearby, add a dedicated breaker. Then patch the drywall, then paint. On an occupied commercial kitchen, multiply by after-hours scheduling.
Ballpark for a 12-foot run with four fixtures: the fixtures might be $280. The electrician, permit, drywall, and paint typically land between $900 and $1,600 depending on market and access. That's your real unit cost — roughly four to five times the product price.
Here's the counterintuitive part. On a leased space with a three-year horizon, hardwiring is usually the wrong call no matter how nice the result looks. You're paying for an improvement you can't take with you, and your landlord may not reimburse it. A plug-in system with proper cord management and a listed power supply is code-compliant in most commercial applications, removable, and roughly half the TCO. I know — it feels less "professional." But the spreadsheet doesn't care how it feels.
On owned property, flip the logic. Hardwired wins on long horizons because you eliminate cord clutter, reduce trip hazards in tight workspaces, and stop replacing cheap plug-in adapters every 18 months. Same product, opposite recommendation. That's the whole point of sorting scenarios first.
Scenario 4: Multi-site buying and controls lock-in
Once you're buying for five buildings instead of one, the decision stops being about fixtures and starts being about ecosystems. If you standardize on a Zigbee-based control system, or on a proprietary app ecosystem like Cync, you're not just buying lights — you're buying a migration path, or the lack of one.
Ask the vendor what happens to your controls when the product line is discontinued. Ask whether the gateway is cloud-dependent, and what you lose if the cloud service shuts down. Ask whether a third party can integrate. The answers are usually less reassuring than the sales deck.
The classic hidden cost is the gateway. You buy 400 fixtures at a great per-unit price, then discover the controls gateway is licensed per site at $1,800 a year, per building. Multiply by five buildings over eight years and the "deal" has quietly added $72,000 to your TCO. That's the kind of number that should be on page one of the quote, and rarely is.
This is also where brand ownership matters again. When a lighting business changes hands, the smart-controls roadmap is often the first thing to get re-scoped. That's not a knock on any particular owner — it's just how post-acquisition integration works. Budget for a second migration in year seven, and you'll rarely be surprised.
How to figure out which scenario you're in
Three questions, in this order:
- Do the fixtures already exist? If yes, you're in Scenario 1 until proven otherwise. Run an end-of-life check on every lamp and fixture SKU before you do anything else.
- Is service access harder than a ladder step? If yes, Scenario 2. Price the maintenance access before you price the fixture.
- Will the install involve opening a wall? If yes, Scenario 3 — and the labor estimate comes before the product comparison.
If none of those apply and you're buying for multiple sites, you're in Scenario 4. Your job there is to make the lock-in cost visible on the spreadsheet before anyone signs a five-year controls contract.
Bottom line: the vendor comparison only makes sense after you've sorted the scenario. Comparing unit prices across different scenarios is how procurement teams end up with a great deal on the wrong product. Not a disaster, exactly. Just an expensive way to be right about the wrong thing.
This was accurate as of Q1 2025. Lighting regulations and brand ownership change fast — the fluorescent rules in particular are still moving — so verify current pricing, availability, and compliance before you budget. I've been burned by assuming yesterday's rules still applied. Twice, actually. The second time was avoidable.
Discuss a lighting project
Share the application, fixture family, control intent, and timing if this article connects to an active specification question.
Tell FLOS what you are planning
Share fixture type, site conditions, target schedule, and any controls requirements. Our team will route the request to the right specialist.